Install Gerson traveling head die cutting machine manual

Install Gerson traveling head die cutting machine manual

Please see the details manual for Gerson traveling head cutting machine.

Before install :

1.Make the site where the machine is to be installed be smooth and level.The strength grading of the floor cement is not lower than R525#
2.Power supply: 380V,50Hz,3-phases Or 220V 3-phases,60Hz etc.,(Same as the customers power requirement).

Ready for install:

1.Get rid of grease or oil on the worktable,Clean each oil sealed part with cleaning oil.

2.Install part 1and part 2 respectively according to indicative identifications on the main machine body.Connect the plug on part 2 into the position on the main machine body（There is no need of worrying about connecting the plug wrongly since there is only one position for connection.This position is the correct)

3.Use a leveling instrument to test whether the worktable is level in longitudinal and horizontal direction to make the level accuracy not be larger than 0.1/1000.

The machine must be installed at a place where is large enough space for operators to the machine.And it must be installed at a place easy for charging and discharging.Space between the machine and the wall is lager than 20cm.

4.Open the cover on the rear of the machine.Then open the square cover on the oil tank.Add 90L hydraulic oil into the oil tank.

It is advised to use MOBLE DTE 25 or SHELL TELLUS 46 or hydraulic oil that is equivalent to ISO VG 46

5.Connect the machine with power supply according to electric principles and requirements and make the machine be ground protected reliably.

Ask professional persons(or electrician)to make the machine be ground protected reliably.

6.Dot press down the button for motor’s start(“Dot press down”means that immediately after pressing down the button for motor’s start,rapidly press down the button for oil pump motor’s stop)

7.Observe the flywheel’s rotation wheel to be in agree with the arrow’s direction on the motor’s case.Start the motor’s run button,running idle for two minutes,then let it to try to operate for several times under zero load.

8.Cut off the power switch,the traveling head press stops.

Have Question? Ask Now

Related Products:

What do you need when install Gerson die cutting machine What do you need when install Gerson die cutting machine ? 1.First ,Must take care…
How to adjust when changing cutting die for Gerson… How to adjust when changing cutting die for Gerson traveling head press When you finish…
Gerson GRM traveling head cutting machine Gerson GRM traveling head cutting machine is mainly used for cutting and laying off various…
Gerson GRM traveling head press operation rules Operators must be familiar with and strict obey the followings rules when use Gerson traveling…
Manual Travelling Head Press Gerson travelling head press both have manual feed and automatic feed.The manual traveling head press…
Manual full head press Manual full head press is manual feed material soft and semi-rigid material into the full…
Gerson CNC moving head die cutting machine Gerson CNC moving head die cutting machine is one traveling head press that build by…
Traveling Head Die Cutting Press Gerson traveling head die cutting press is great ideal die cutting machinery for roll or…
Rubber Manual Fixed Head cutting machine Rubber Manual Fixed Head cutting machine is applicable to die cutting operation of crosslink polyethylene foam, neoprene-blend rubber, EPDE rubber for making foam or rubber closure strips, which eliminate moisture absorption and water vapor transmission. Key Feature 1. The adoption of hydraulic system improves the cutting efficiency without any noise. And the setting of the machine is easy to adjust to fit the demand. 2. The rigid and sturdy framework and auto balance mechanism make sure that the machine can work in a state of equilibrium, thus guaranteeing each cutting operation to reach the same depth. What's more, the four-oriented design and double cylinders as well as many other parts make for high performance of the machine. 3. Pressure larger than 25T can be provided by our cutting machine. 4. A series id feed devices can be optionally installed with higher efficiency and less material waste: Single or Double, Manual or automatic slide table Pneumatic pinch rolls Clamping beam feeds Inboard and outboard motorized conveyor belts Continuous cutting belts Sheet feeds Edge sensing 5. Apart from this machine, we also have a large variety of cutting machines for selection. We have already had proven technique in die cutting these materials: Polyurethane Foam for bedding, cushioning, protective packaging or sound studios, to Polyethylene Foam for…
clicker die cutting press traveling head The Gerson clicker die cut press with traveling head have used in many industries.These industries…