Die Cutting Machine
38 Years+ Manufacturer
Quote Now

Atom cutting machine

ATOM have been producing cutting machine since 1946 .Now they have the following hydraulic cutting machine:

1.swing arm cutting machine

Atom produces four main types of swing beam cutting presses, these include:

SE Series (Entry Level)

se-atom-cutting-machine

This swing beam cutting press is extremely simple to use with easy adjustment of the cutting stroke, an operator can switch between multiple height cutting dies without any setting or adjustment.

The control push buttons are ergonomic, so allowing the operator increased comfort. The push buttons are controlled by a two hand safety relay, meaning the buttons need to be activated 5/10ths/sec between each other too allow cutting stroke activation, and requires constant activation to maintain a cut stroke.

The cutting power is easily adjusted if required through the movement of a simple potentiometer on the cutting beam.

A functional machine, constructed in the same way as other models, but even simpler to use. The basic machine, with automatic setting of stroke end, working with dies of different height is not a problem.

Model Cutting Table UP Beam Head Max Pressure Net Weight
SE25L 1000×500 610mm 25T–245Kn 1050 (kg)
SE25 1000×500 500mm 25T–245Kn 1030 (kg)
SE25C 900×450 500mm 25T–245Kn 900 (kg)
SE24 1000×500 370mm 25T–245Kn 990 (kg)
SE24C 900×450 370mm 25T–245Kn 880 (kg)
SE22 1200×500 500mm 22T – 216Kn 1060 (kg)
SE20 900×450 370mm 22T – 216Kn 880 (kg)
SE20C 900×430 370mm 22T – 216Kn 630 (kg)
SE8 600×300 300mm 8T – 78 Kn 430 (kg)

S100 Series

atom-cutting-machine-s100

This type of cutting press is equipped with three different cutting pressures to enable the use of different sized (surface area) dies without any repeating adjustments.

The S100 swing beam cutting press is like the SE Series simple to use with easy adjustment of the cutting stroke, an operator can switch between multiple height cutting dies without any setting or adjustment.

Unlike the SE swing beam the S100 has a 3 push button cutting power selection rack, this means that as an operator moves from a smaller die to a larger tool (surface area) rather then adjust the cutting power settings, any 1 of 3 buttons can be used on the left push button console to achieve an accurate cut.

The cutting power is easily adjusted if required through the movement of a two potentiometers on the cutting beam, the smaller of the two adjusts the 1st button of the 3 and the larger controls the 3rd push button. The 2nd push buttons cutting power is an average taken between the smaller and larger settings.

The control push buttons are ergonomic, so allowing the operator increased comfort. The push buttons are controlled by a two hand safety relay, meaning the buttons need to be activated 5/10ths/sec between each other too allow cutting stroke activation, and requires constant activation to maintain a cut stroke.

The specifications and models available within this range are listed below:

All S100 Series swing beam cutting presses are supplied with a CE Mark of conformity.‘Multiforce’ (light swing)

multiforce atom cutting machine

This system automatically adjusts the cutting pressure required to increase ease of use, reducing the wear on the cutting board (up to 50%) and maximising energy economy.

The ‘Multiforce’ differs from other swing beam cutting presses by operating to a stroke end system, therefore meaning it reaches the same depth each time. It also boasts the ‘light swing’ arm, which makes arm movement by the operator effortless.

The ‘Multiforce’ device allows a cutting board saving of up to 50%, so not only saving money, but also allowing better cutting across the board due to less wear, and so board reduced contours.

The ‘light swing’ arm can be supplied in a super light alloy, so yet again decreasing weight on the cutting beam, and so minimising operator effort required, and reducing fatigue.

Have Question? Ask Now